Guide

How to Reset a Honeywell Safe

Updated on · By the Flood of Dollars team

To reset a Honeywell digital safe, press the program button inside, enter a new 3 to 8 digit code, and press the lock key to save it. If you've forgotten the current code, open the safe with the backup key and program the new code from there.

On this page (7 sections)
  1. What does resetting a Honeywell safe actually do?
  2. Where is the reset button, and what do the beeps mean?
  3. How to reset a Honeywell safe code when you still know the old one
  4. How do you reset the code when you've forgotten it?
  5. Why won't the keypad take a new code?
  6. What should you do after a successful reset?
  7. Which safe suits a reset without hassle?

To reset a Honeywell safe access code, open the door with the current code or the backup key, press and hold the program button inside until the keypad beeps, then enter a new code and press the lock key to save it. That is the whole job on a Honeywell digital keypad safe, and it takes about a minute.

The answer above applies to the programmable models, including the Hideable Safe in the 6100 series. Key-locking chests and lock boxes use physical keys instead, so there is no code to change on those.

If your safe won't open at all right now, start with how to open a Honeywell safe and come back here once the door is open.

What does resetting a Honeywell safe actually do?

Resetting changes two things: the code the keypad accepts and the state of the lock once the code is saved. It does not wipe your contents, move the bolt, or restore a factory code that nobody publishes.

On a keypad model the save step overwrites the old code. Only one code is active at a time, so you enter the new digits and the previous sequence stops working immediately.

The two backup keys are untouched by a reset and keep working exactly as before.

If the safe is refusing a code you know is right, a reset usually is not the fix. A tired battery, a rushed keypress, or a code typed too quickly after waking the panel are far more common causes.

Make the keypad power up cleanly first, then reset only if the code really needs replacing.

The reset does not change how the door itself behaves. The concealed hinge on the 6108 still guards the door edge, and the bolt still throws the same way it did before.

What you are replacing is the entry credential, not the hardware.

Where is the reset button, and what do the beeps mean?

The reset button sits inside the safe, not on the outside keypad. Open the door and look along the inner door edge, near the battery compartment; Honeywell's small safe models put it behind or beside that cover.

A single short beep typically confirms the safe has accepted the button press and is ready for a code. A run of quick beeps usually means the code was too short, too long, or the keypad didn't register every digit.

Slide the battery cover off and check that the cells sit flat before you press anything else.

The program button only responds while the door is open. That is deliberate: it means someone standing at a locked safe cannot reach the reset at all, and the only ways in are the code or a key.

On the 6108 the button sits close to the touchpad wiring, so press it firmly but don't tug on the cable.

How to reset a Honeywell safe code when you still know the old one

Enter the working code, open the door, then program the new code from the inside panel. This is the normal reset path, and you don't need a key for it.

  1. Wake the keypad and key in the current code.
  2. Turn the knob or press the handle to swing the door open.
  3. Press and hold the reset button until the panel beeps once.
  4. Key in the new code, then press the lock key.
  5. The panel beeps again to confirm the save. Test it with the door open before you close it.

If you want the same style of safe on another shelf, the Honeywell fireproof safe lineup shows which sizes take a digital code and which stay key-only. The small 6108 accepts a code you set, which is why owners bother resetting it in the first place.

Do the test with the door ajar every time. A new code that saved but reads wrong on the first try is common, and you want to find that out before the door shuts.

With the door open, the keypad's touchpad stays lit long enough to try the code twice, so you can be sure the digits stuck before you latch it.

How do you reset the code when you've forgotten it?

Open the safe with a backup key first. The hidden keyhole sits behind a small cap or cover on the front door, often under the keypad housing; turn the key, then press the handle down.

With the door open, press and hold the reset button until it beeps. Enter the new code and press the lock key, then enter the code a second time to confirm it works.

That step is the practical version of the how to reset a Honeywell safe question people search when the code slips their mind.

What you can't do is reset a Honeywell safe from the outside with no key and no code. The keypad doesn't have a visible default code, and the maker does not publish a universal one.

If both keys have gone missing too, call Honeywell Safes support or a locksmith and have the model number from the back of the door ready. Forcing the door bends the bolt and the frame and is the most expensive option on the list.

What about the 6104 lock box and the 1103 fire chest?

Those two are key-only, so there's no code to reset. The reset steps here simply don't apply to them.

The Honeywell 6104 Lock Box uses a key lock with two entry keys, and the interior is foam padded so loose items don't slide around. If you need a code on a small box, the 6108 is the one to look at instead.

It opens with two keys and has no touchpad to program and no program button to find inside.

The Honeywell 1103 Fire Chest is key controlled as well, with a carry handle and a lid that holds letter and A4 paper flat. Its job is fire and water protection for documents, not code management.

That is also why it weighs 27.4 pounds: the molded fire and water insulation goes into the shell rather than into a keypad.

If you're choosing between this digital reset path and a simpler key-only box, our SentrySafe vs First Alert comparison covers the wider market, while the SentrySafe SFW123GDC review shows a rival keypad safe with its own reset routine.

Why won't the keypad take a new code?

Most failures are power or timing, not a broken reset. Work through these in order before assuming the safe needs replacing.

  • Battery: fresh cells first. The panel can flash or beep weakly as the battery dies, and a reset can't save on a flat supply.
  • Press speed: type at a steady pace with a short gap between digits. Very fast entry makes the panel drop a key.
  • Button hold: hold the reset button until the beep, not for a guessed count. Letting go early cancels the program mode.
  • Lock key: finish with the lock key every time. A code typed without it is not saved, so it fails on the next try.

If the safe opens on the old code but never accepts a new one, the panel isn't entering program mode and a new battery is the next step. When it opens on neither the old code nor a fresh one, fall back to the backup key and reset once more.

Enter the code slowly enough that each keypress registers on the touchpad before the next one lands.

What should you do after a successful reset?

Write the new code down somewhere away from the safe and test it twice with the door open. Pick digits you can recall under pressure rather than a string that's easy to guess.

Store the backup keys outside the safe, one in a drawer and one with someone you trust. Honeywell includes two keys with the 6108 for exactly this reason: a forgotten code becomes a two minute job when a key is within reach.

The 6108 also gives you a foam padded floor, so whatever sits on top of the mat doesn't pick up scratches while you are busy resetting.

Keep the keypad clean and dry, and change the battery on a fixed date each year. For keypad and battery details on similar boxes, see Honeywell fireproof safe models.

A safe that takes a code should be tested on that date too, so you never find out the battery is flat on the morning you need the contents.

Which safe suits a reset without hassle?

If you reset codes often or would rather skip keypads, pick the model that matches how you lock it. The how to reset a Honeywell safe routine is quick on the digital 6108 and unnecessary on the key-only boxes.

The 6108 Hideable Safe gives you a programmable code plus two backup keys, double steel walls, and a foam floor mat, so it fits a shelf or a wardrobe floor and still gives you a code route out of trouble. Its mounting options include wall and floor mount, which suits a spot you don't want moved.

The 1103 Fire Chest is the one to keep beside your document folder, since its carry handle makes it easy to grab and its lid holds flat papers. It carries a 30 minute UL fire rating and a waterproof seal, so it covers the flood and fire job the 6108 only partly handles.

The 6104 is the simple lock box: key lock, two keys, padded floor, and nothing to program. Its exterior is just 4.1 inches tall and it weighs 7.9 pounds, so it slips onto a closet shelf without a fuss.

Any Honeywell keypad safe resets the same way, so learn the routine once and it transfers. The key-only models never need it.

Frequently asked questions

Where is the reset button on a Honeywell safe?

It sits inside the door frame, usually on the hinge side of the battery cover. Honeywell calls it the program or reset button, and you can only press it with the door open after entering a working code or using the backup key.

Can I reset the code without the old one?

Yes, if you have the backup keys. Turn the key to open the door, hold the program button until the panel beeps, then type the new code and press lock.

Without a key or the old code, Honeywell safes are built to stay shut, so contact Honeywell Safes support with your model number.

How long should a Honeywell safe code be?

Honeywell keys safes accept 3 to 8 digits, and most owners settle on 4 or 5. Use digits you can recall without writing them beside the safe, and avoid obvious strings like 1234 or your birth year.

Why does my Honeywell keypad flash or beep and not open?

A dead battery or faster repeated presses are the usual causes. Fit fresh batteries, wait for the panel to settle, and type the code with a short pause between digits.

Hold the key turned for a moment before pushing the handle down.

Does resetting the code erase my stored code?

Yes. The save step replaces the existing code, so write the new one down somewhere away from the safe before you close the door.

The factory default is not published, so the backup key is your only route back in.